Differences

This shows you the differences between two versions of the page.

--- ultimaker_3_extended:ultimaker_3_extended [2019/09/23 11:08] – [Yearly] formlab
+++ ultimaker_3_extended:ultimaker_3_extended [2026/09/11 21:43] (current) – external edit 127.0.0.1
@@ Line 1: / Line 1: @@
 ====== Ultimaker 3 Extended ======
 {{:ultimaker_3_extended:ultimaker_3_extended.png?nolink&200|}}
+  * Max Build Volume: ''215 x 215 x 300mm''
+  * [[:Filament options]]
+[[https://www.formlab.schoolofarts.be/pricing|How much does FDM printing cost?]]
+----
 ===== Maintenance =====
-==== Monthly ====
+==== Every 2 months ====
   * [[https://ultimaker.com/en/resources/23131-clean-the-printer|Clean printer]]
+    * wash build plate with warm water
+    * heat up nozzles to 150°C and remove plastic stuck on the nozzle (with tweezers or a paper towel)
+    * clean Bowden tube by pushing a piece of sponge trough. Tight fit, and a new piece of sponge per tube.
   * [[https://ultimaker.com/en/resources/23130-lubricate-the-axles|Lubricate axles]]
+      * clean all smooth axles with a paper towel
+      * one drop of Unilube on all smooth axles (also the two vertical ones). Move the print head and bed manually to distribute.
-==== Every 3 months ====
+==== Every 6 months ====
   * [[https://ultimaker.com/en/resources/52500-check-for-play-on-axles|Check for play on axles]]
+      * [[https://ultimaker.com/en/resources/50871-check-for-play-on-axles|calibrate axles if play detected]]
   * [[https://ultimaker.com/en/resources/39664-check-the-tension-of-the-short-belts|Check tension of short belts]]
-  * [[https://ultimaker.com/en/resources/52501-check-for-residue-in-the-front-fan-of-the-print-head|Check for residue in front fan of print head]]
+  * [[https://ultimaker.com/en/resources/50869-check-for-residue-in-the-front-fan-of-the-print-head|Check for residue in front fan of print head]]
   * [[https://ultimaker.com/en/resources/52502-check-the-quality-of-the-silicone-nozzle-cover|Check quality of silicone nozzle cover]]
   * [[https://ultimaker.com/en/resources/23132-clean-the-print-cores|Clean print cores]]
@@ Line 19: / Line 33: @@
   * [[https://ultimaker.com/en/resources/52504-clean-the-feeders|Clean feeders]]
   * [[https://ultimaker.com/en/resources/52505-replace-the-bowden-tubes|Replace Bowden tubes]]
+===== Troubleshooting =====
+==== Printer not in remote clusters  ====
+✔ Solved\\
+/04/2026
+When you want to print via cloud you get the message 'printer not in remote clusters'.
+In the browser, go to [[https://digitalfactory.ultimaker.com/|Digital factory]] and remove the printers that you can't print on via the cloud.
+Restart the computer.\\
+Make sure that cura is not open. Then go to the printer.
+On the printer
+  * system > Maintenance > Digital Factory reset. (The printer restarts)
+  * after the restart, go to system > netword > Digital Facotory > Connect to Digital Factory. You'll get a 6 digit code
+(you don't need a firmware upgrade. they are now on 5.3 which is the highest firmware. (Unmaintained, no new firmware updates coming)).
+On the computer, go to [[https://digitalfactory.ultimaker.com/|Digital factory]] again and add a new printer. Select the 'S' printer type and add the code to pair up the printer. The printer shows it's offline, but after a minute or two it changes to the active online status.